Rikon Power Tools 25-210 Manuel du propriétaire

25-210H25-210www.rikontools.com25-210/HM112” Planer / Jointer 25-210H Helical w/ Knife Inserts & 25-210 Straight Knife models Operator’s ManualRec

ADJUSTMENTSJOINTER FENCE ADJUSTMENTThe jointer fence provides lateral support for the workpiece when surface planing.1. After loosening the Locking H

11PLANER TABLE HEIGHT ADJUSTMENTHeight adjustment of the planer's table is made with the Handwheel (#168, FIG. 11, A). One full turn of the crank

12ADJUSTMENTSROTATING OR REPLACING KNIFE INSERTS - For the 25-210H Helical Planer/JointerThis machine has a helical cutterhead with four rows of HS

13ADJUSTMENTSTable Alignment continued from page 12FIG. 18FIG. 19FIG. 20NOTE: It may be easier to remove the fence assembly and guard for this exercis

14ADJUSTMENTSFIG. 21ADJUSTING THE INFEED TABLEThe Infeed Table is pre-set by the factory to align with the cutterhead's knife inserts. Should an

15ADJUSTMENTSPlaner Table Alignment continued from page 141. Make sure that the planer/jointer's switch is turned off, and the plug is disconnect

16ADJUSTMENTS THE MACHINE MUST NOT BE PLUGGED IN AND THE POWER SWITCH MUST BE IN THE OFF POSITION UNTIL ALL ADJUSTMENTS ARE COMPLETE.ADJUSTING THE

17ADJUSTMENTSTo inspect, adjust or change the drive belts:1. Make sure that the planer/jointer's switch is turned off, and the plug is disconnec

18ADJUSTMENTSSTART BUTTONDuring transit or after long periods of use, the planer knives may have shifted out of alignment. It is important to check th

19ADJUSTMENTSREPLACING PLANER KNIVESREMOVING PLANER KNIVES1. Unplug the machine and put the power switch in the OFF position until all adjustments ar

2TABLE OF CONTENTSSPECIFICATIONSNOTE: The specications, photographs, drawings and information in this manual represent the current models when the ma

The function of the jointer is to surface plane at, one side or edge of a board/workpiece. To use the jointer:- Place the workpiece on top of the ri

FIG. 42PLANER OPERATIONThickness planing is used to reduce a workpiece with one already surface planed surface to a desired thickness.To use the plane

OPERATIONSNIPEThe term 'snipe' refers to the depression that may occur at the front or rear of a board during planing. It is caused by uneve

23MAINTENANCE1. Before each use:- Check the power cord and plug for any wear or damage.- Check for any loose screws or hardware.- Check the area t

SYMPTOM POSSIBLE CAUSES SOLUTIONSMachine will not start. 1. No power2. Blown fuse3 . M a i n o n / o f f s w i t c h o r M i c r o

SYMPTOM POSSIBLE CAUSES SOLUTIONSTROUBLESHOOTING THE PLANERPoor feeding of lumber through the planer1. Drive belt is worn or broken2. Drive belt tensi

PARTS DIAGRAM26NOTE: Please reference the Key Number when calling for Replacement Parts.For Parts under Warranty, the Serial Number of your machine is

27PARTS LISTCABINET ASSEMBLYKEY NO. PART NO.Lock nutSwitch plateMicro switchPan screwLock nutFlat washerHex screwIdle pulleyRingBearingTubeAdjust cush

PARTS DIAGRAMCUTTERHEAD ASSEMBLY28HELICALASSEMBLY

29CUTTERHEAD ASSEMBLYPARTS LISTKEY NO. PART NO.NOTE: Please reference the Key Number when calling for Replacement Parts.For Parts under Warranty, the

3SAFETY SYMBOLSIMPORTANT! Safety is the single most important consideration in the operation of this equipment. The following instructions must be

PARTS DIAGRAM30PLANER TABLE ASSEMBLYNOTE: Please reference the Key Number when calling for Replacement Parts.For Parts under Warranty, the Serial Numb

PARTS LISTPLANER TABLE ASSEMBLYKEY NO. PART NO.ScrewRodPlaner tableIndicatorSpring washerHexagonal head screwTubeSet screwLocking plateLocating sleeve

PARTS DIAGRAMINFEED TABLE ASSEMBLYNOTE: Please reference the Key Number when calling for Replacement Parts.For Parts under Warranty, the Serial Number

PARTS LISTINFEED TABLE ASSEMBLYKEY NO. PART NO.Hex screwSpringSupport baseNutHex screwEccentric shaftScrewFront RackScrewHex screwGuide plateSupport b

PARTS DIAGRAMNOTE: Please reference the Key Number when calling for Replacement Parts.For Parts under Warranty, the Serial Number of your machine is r

35PARTS LISTKEY NO. PART NO.Hex screwGuide plateWasherLocknutBoltSpring washerHex screwRodBack rackCutterhead guardRodHex cap screwGuard assemblyBig d

36PARTS DIAGRAMFENCE ASSEMBLYNOTE: Please reference the Key Number when calling for Replacement Parts.For Parts under Warranty, the Serial Number of y

37PARTS LISTFENCE ASSEMBLYKEY NO. PART NO.Adjust handleNutLock cylinderWasherHex screwLeft support armSupport plateBig washerAngle indicatorWasherHex

38PARTS DIAGRAM & PARTS LISTNOTE: Please reference the Key Number when calling for Replacement Parts.For Parts under Warranty, the Serial Number o

39PARTS DIAGRAM & PARTS LISTHex socket cap screwWasherMotorBig washerCap nutSpring washerHex screwMotor pulley (25-210)Motor pulley (25-210H)Self-

4SAFETY INSTRUCTIONS 16. NEVER LEAVE A RUNNING TOOL UNATTENDED. Turn the power switch to the “OFF” p

www.rikontools.com25-210/HM1For more information:16 Progress RoadBillerica, MA 01821877-884-5167 / [email protected]

5 THIS SYMBOL DESIGNATES THAT THIS TOOL IS LISTED BY THE INTERTEK TESTING SERVICES, TO UNITED STATES AND CANADIAN STANDARDS. S

6SPECIFIC SAFETY INSTRUCTIONS FOR PLANER / JOINTERS 1. Do not operate this machine until you have read all of the following instructions. 2. Do no

7GETTING TO KNOW YOUR MACHINECarefully unpack your machine from its carton. Check for any shipping damage, and make sure the following parts are inclu

INSTALLATION8AUnpacking and Clean-up1. Carefully remove all contents from the shipping carton. Compare the contents with the list of contents to make

ASSEMBLYFIG. 3FIG. 4FIG. 5FIG. 69AINSTALLING THE POWER PLUGThe Planer/Jointer is shipped without an electrical 220 volt plug, so that the correct plug